HOME TM1016R

TM10-16R   10-inch Broadcast Color Monitor

 

Ikegami's TM10-16R is a High Performance. Low Cost Monitol: The unit is specifically designed for production and broadcast applications and produces high-fidelity video reproduction with easy operation by utilizing In-Line Gun CRT technology, Comb Filter, A/B/RGB and Y/C Video inputs.

  • In-Line Self Converging Electron Gun assures convergence stability.
  • Black Matrix surrounding CRT face assures high contrast under bright ambient illumination.
  • Flat square CRT assures easy-to-observe picture.
  • Comb Filter provides wide band luminance, switchable to notch filter at front panel.
  • Feed-Back Clamp provides excellent Black Level Stability with varying APL.
  • Pre-Set Operating Controls.
    Chroma, Brightness, Contrast.
  • Sweep failure protection circuits prevent phosphor burns.
  • The TM10-16R can be supplied for use either from AC power (standard) or from DC power (option) by replacing power unit.
    When the optional bracket is used in conjunction with the DC power unit, the TM10-16R can be operated by battery (option).
  • BLUE ONLY function
    A front panel switch allows the blue signal to be applied simultaneously to R, G and B channels This makes for easy hue and color level checking using a color bar signal feed to the monitor.
Specifications
GENERAL
1.0 Input Voltage (Nominal value) 100-120V /200-240V AC ±10% (Specify when ordering)
Single phase, 50/60 Hz
12V /24V DC ±10%
(DC operation can be effected by replacing the AC power unit with the DC power unit)
2.0 Input Power Approx 40W (at normal operation) 3.0 Input Signals 1) Video Inputs
Encoded Video
Composite (10Vp-p nominal) or Non-composite (0.7Vp-p nominal), positive polarity, two (2) each

R/G/B Video
Non-composite (0.7Vp-p nominal) or Composite (1.0Vp-p nominal), positive polarity, one (1) set (requires external sync or green on sync)

Connection
Video A/B : Bridging BNC connectors, high impedance RGB : Terminated 75 ohm

2) Composite Sync Input
Standard Sync
4Vp-p ±2Vp-p nominal, negative polarity, one (1)

Separate Y /C Video
Y: 1.0Vp-p positive polarity, 75 ohms terminated
C: 0.286Vp-p (Burst signal), 75 ohms terminated

Connection
Bridging BNC connectors, high impedance

3) Remote Control Functions
a) Video input selector (A/B/RGB/Y/C)
b) Sync mode (Internal/External)
c) Color/Monochrome select
d) Tally (ON/OFF)
4.0 Vertical Sweep Rate Nominal 59.94 Hz 5.0 Horizontal Sweep Rate Nominal 15.734 kHz 6.0 Scanning 525 lines/ frame
60 field/ second
30 frame/ second
2:1 interlace
7.0 Display Device
1) CRT Type
In line gun, Slot-shadow mask, Medium resolution CRT

2) Size
9V

3) Mask Pitch
0.47 mm (Horizontal)

4) Resolution (at center)
310TV lines (at 50 ft-L)
8.0 Video Signal System 1) Frequency Response
(measured with aperture gain 0, 3.58 MHz notch filter removed)
50 Hz- 7 MHz flat within ± 1/3dB (referred to 100kHz)

2) Pulse Response
(at each R/G/B amplifier output with 0.05 micro sec. rise time square wave video input)
Overshoot < 10% with 250 kHz square wave
Sag < 5% with 60Hz square wave

3) Chrominance Rejection Ratio
(measured with aperture gain 0, notice filter ON)
Less than -24dB

4) Aperture Correction
Correction characteristics:
Waveform of overshoot of 2T pulse appears symmetrically with notch filter ON

5) Noise
(measured at each R/G/B channel in active scan period)
Coherent noise -40dB
Hum noise -50dB
Other noise -50dB
9.0 Color Signal System
1) Chroma Signal Frequency Response
(measured at chroma output test point when video sweep signal of 1.0Vp-p composite is supplied at video input)
3.58 MHz ±0.5 MHz, flat within ±1/3dB

2) Demodulation Axis Phase Difference
90° ± 2°
10.0 Sync System
1) Sync Stability
Stability of synchronization will be met for the following conditions

Internal Sync
Video input level change of :!:6dB from the rated value to 1.0Vp-p

External Sync
Sync signal input level between 1 and 8Vp-p

2) Vertical Hold
Holding Range
Vertical hold will be maintained at 59.94 Hz

Interlace Ratio
The interlace ratio will be ±5%

3) Horizontal Hold
Holding Range
Pull in range will be ± 300 Hz
Holding range will be ± 700 Hz

AFC Time Constants
Two (2) horizontal time constants will be provided
a) 2msec
b) 0.5msec
11.0 Deflection System
1) Scanning Amplitude (Normal scan)
Adjustable to 1% of CRT effective area with an aspect ratio of 4:3

2) Geometry and Linearity
Less than 2% of picture height

3) High Voltage
Tolerance
18kV ±1kV

Regulation
±5% over the range of 0 - 300 micro A referred to 100 micro A
12.0 Ambient Temperature
0°C -40°C
90% or less relative humidity (non-condensing)
13.0 Mechanical
1) External dimensions
222 (W) x 213 (H) x 352 (D) mm (w/o Battery)
(8.7 x 8.3 x 13.8 in.)

2) Weight
Approx 9kg (20 lb)
Design and specifications are subject to change without notice.
Home | All Products | Contact | Site Map |