Specifications
| General |
|
Input Voltage
|
AC100-120V/200-240V ± 10% (automatic select)
50Hz/60Hz, single phase
DC12V/24V ± 10%
|
|
Input Power
|
AC input 70W
DC input 45W
|
|
Input Level
|
Video Signal:
VS 1.0Vp-p
V 0.7Vp-p, positive
R, G, B Signal:
VS 1.0Vp-p
V 0.7Vp-p, positive
Component Signal:
NTSC :
Y VS 1.0Vp-p
V 0.714Vp-p, positive
R-Y 0.7Vp-p
B-Y 0.7Vp-p
PAL :
Y VS 1.0Vp-p
V 0.7Vp-p, positive
R-Y 0.525Vp-p
B-Y 0.525Vp-p
Y/C Signal:
Y VS 1.0Vp-p, positive
C 0.286Vp-p (burst level)
Sync Signal:
40Vp-p ± 2Vp-p, negative
|
|
Input Impedance
|
Video, Sync. High impedance bridge connection or terminated 75 ohm
R, G, B/Component, Y/C. Terminated 75 ohm
|
|
Remote Controls
|
a) Video input select (A/B)
b) VIDEO/AUX (RGB or COMPONENT)
c) VIDEO/Y/C
d) Sync mode select (INT/EXT)
e) COLOR/MONO
f) TallyON/OFF
|
|
Vertical Sweep Rate
|
Nominal, 59.94Hz (NTSC), 50Hz (PAL)
|
|
Horizontal Sweep Rate
|
Nominal, 15.734kHz (NTSC), 15.625kHz (PAL)
|
| Performance
|
|
1) Resolution
|
550TVlines (at center)
|
|
2) CRT
|
In-Iine gun dot shadow mask, high resolution CRT
(0.28mm dot trio pitch)
|
| Video Signal System
|
|
1) Frequency Response
|
Measured with Aperture Gain 0, Trap
(3.58MHZ: NTSC, 4.43MHz: PAL)
removed: 60Hz- 7MHz
±1/3dB referred to 100kHz
|
|
2) Pulse Response
|
At each, R, G, B, amplifier output with 0.05 micro Sec.
rise time square wave video input.
Rise time <0.1 micro sec. (at 250kHz)
Overshoot <10% (at 250kHz)
Sag <5% (at window signal)
|
|
3) Chrominance Rejection Ratio
|
Measured with Aperture OFF,
Trap (3.58MHZ' NTSC, 4.43MHZ'.PAL) ON.
Less than -25dB at color bar signal
|
|
4) Aperture Correction
|
Waveform of overshoot of 2T pulse appears
symmetrically with Trap
(3.58MHZ: NTSC, 4.43MHZ: PAL) ON
|
|
5) Linearity (Differential Gain)
|
Less than 5% from video input terminal to each R, G, B output terminal
|
|
6) Noise
|
Measured at each R, G, B channel in active scan period
Coherent Noise: -46dB
Hum Noise: -50dB
Others: -50dB
|
| Color Signal System
|
|
1) Chroma Signal
|
Measured at chroma output test point: 3.58MHz ± 0.5MHz
|
|
Frequency Response
|
±1/3dB (NTSC), 443MHz ± 0.5MHz ±1/3dB (PAL)
|
|
2) Demodulation Axis Phase Error
|
90° ± 1
|
| Sync System
|
|
1) Sync Stability
|
Stability of synchronization will be met for the following conditions.
|
|
Internal Sync
|
a) Video input level change of ± 6dB from the rated value.
b) Video amplitude change of 0 to 120% and sync levels greater than -6dB (0.15V to 0.3V sync)
|
|
External Sync
|
1Vp-p - 8Vp-p
|
|
2) Vertical Hold
|
|
Oscillator Frequency
|
Variable between 45Hz and 65Hz (controlled by V. HOLD)
|
|
Interlace Ratio
|
± 5%
|
|
3) Horlzontal Hold
|
|
Oscillator Frequency
|
14.75kHz to 16.75kHz (controlled by H. HOLD)
|
|
Holding Range
|
Pull-in range ± 300Hz Holding range:± 1KHz
|
|
AFC Time Constants
|
0.5msec. and 2msec (selectable on FRONT PANEL)
|
| Deflection System
|
|
1) Effective CRT screen size
|
156 (H) x 117 (V) mm
|
|
2) Scanning Amplitude
|
NORMAL:
1% overscan of CRT effective area at aspect ratio of 4.3
UNDER:
15% underscan of CRT effective area at aspect ratio of 4:3
|
3) Deflection Distortion
(Linearity and Geometry)
|
Less than 2% of picture height
|
|
4) Retrace Time
|
Horizontal: 10 micro-Sec. or less
Vertical: 1msec or less
|
|
5) Hum Oscillation
|
Less than 0.2mm
|
|
6) Convergence
|
|
Picture Center
|
Within a circle of 80% of picture height Less than 0.4mm
|
|
Picture Corners
|
Outside area of picture center Less than 0.9mm
|
|
7) High Voltage
|
Tolerance
18kV ± 1kV
|
|
Regulation
|
± 5% over the range of 0 to 450 microA referred to 150 microA
|
| Audio System (option)
|
|
1) Input Level
|
-20dB
|
|
2) Input Connector
|
Pin jack (RCA type, single end)
|
|
3) Input Impedance
|
10k ohm
|
|
4) Output Level
|
0.8W max.
|
|
Ambient Temperature
|
0°C-40°C (32°F-104°F)
90% or less relative humidity (non-condensing)
|
|
External Dimensions (WHD)
|
222 X 213 X 350mm (8.7 x 8.4 x 13.8 inches)
|
|
Weight
|
Approx. 9.6Kg (21.2 lbs)
|
HOME
TM1019RH
