CCU-980: 3G Camera Control Unit
CCU-980 is a 3G ready fiber transmission Camera Control Unit for UnicamHD series cameras. 3G transmission systems can be configured in combination with 3G ready cameras.
- 3G Wideband transmission between camera head and CCU as well as 1.5G output.
- Selectable multi output port for 3G-SDI/HD-SDI/SD-SDI by the menu.
- 4 channels RET video input as standard. 3G-SDI, HD-SDI and SD-SDI signals are automatically identified.
- By menu selection, HD Q-TV and RET signals output through the MON SDI connecter on the rear of a camera. Both HD Q-TV and Q-TV(VBS) can be used. Capable asynchronous image input and Embeded Audio x 4ch.
- QTV (VBS) x2 as standard. (2nd channel is an option for FA-97A)
- HD-SDI TRUNK for the transmission of different video signal from camera between camera and CCU as option. Multiplexed ANC（Embedded AUDIO etc.）is available in case the signal is synchronized with a camera.(Only in 1.5G mode)
- Camera No. and ARC ID displayed on the front panel are convenient to use as well as capability of PGM3 and Y TALLY as standard.
HDTV System (Input Signals) External Reference Input GENLOCK : Tri-level sync ot BBS 75 ohm BNC x2 (Loop Through)
(HDTV/SDTV automatic detection)
SUB REF : 10 Field ID 75 ohm BNC x2 (Loop Through)
Return Video Input 75 ohm 3G/HD/SD-SDI Single End 4ch or 2ch Active-Through (Menu Selection) Q-TV(prompter) Input HD-QTV: HD-SDI 75 ohm single end 1ch
SDTV: VBS 75 ohm single end 1ch(2ch:factory option)
Output Signals Line Video Output 3G/HD-SDI : Serial Digital 75 ohm BNC 2ch 4 outputs (OUT1/OUT2)
SMPTE 425M, SMPTE 372M, SMPTE292M standard
* 3G-SDI format supports Dual-Link outputs (Menu Selection)
SDTV signals : Serial Digital 75 ohm BNC 1ch 2 outputs(OUT3)SMPTE292M
VBS signal : 1.0Vp-p 75 ohm BNC 1ch 2 outputs
Monitor Video Output 3G/HD-SDI : Serial Digital 75 ohm BNC 1ch 1 output (HD PM)
*SMPTE 425M, SMPTE292M standard
Trunk Video Output HD-TRUNK : HD-SDI 75 ohm single end 1ch(factory option) Intercom(ENG/PROD) 4-wire or Clearcom or RTS
4-wire: 0dBm 600 ohm 2ch
Clearcom : -15dBs 200 ohm 2ch
RTS: 0dBs 200 ohm 2ch
MIC: 0dBs 2ch 2 outputs Low impedance
Tally R/G/Y 3ch OPEN (OFF) / GND (ON) 50mA (max.) Control Arcnet BNC x1ch
Ethernet RJ-45 x1ch
ICCP OCP/CCP x1, CCP/CSU x1
Operating Voltage AC100/110/117/220/240V±10% Power Consumption approx. 80VA (BS only) Ambient Temperature 0°C to +40°C (32°F to 104°F) Relative Humidity 30% to 90% (Non-condensing) Dimensions W218.6 x H125x D457mm
(W8.63 x H4.92 x D18.00 inches)(excluding protrusions)
Weight approx. 28kg (62 lbs) Support Products ・broadcast/HDK-970A/AP